Welcome, Guest. Please Login or Register
Stick and Tissue Logo
 
  HomeHelpSearchLoginRegister  
 
 
Page Index Toggle Pages: 1
Send Topic Print
Request entity too big (Read 706 times)
Reply #8 - Jan 17th, 2017 at 3:56pm

New Builder   Offline
Junior Member
Amherstburg, Ontario, Canada

Posts: 64
**
 
Problem solved. I'll be posting my Ryan STA pics to the New Build section, probably tomorrow morning. Thanks again for all the feedback and help. Irfanview finally made sense and works fine. Smiley
 
IP Logged
 
Reply #7 - Jan 17th, 2017 at 3:08pm

New Builder   Offline
Junior Member
Amherstburg, Ontario, Canada

Posts: 64
**
 
Thanks to all for the help but still having difficulty reducing my photos to a size below 750Mb. Tried resizing a resized photo but no luck. Will keep trying until I find a solution, really want to participate. Thanks again. Sad
 
IP Logged
 
Reply #6 - Jan 11th, 2017 at 1:36pm

Sky9pilot   Offline
Administrator
Stick & Tissue
Kelso, WA 98626 USA

Posts: 7434
*****
 
New Builder wrote on Jan 10th, 2017 at 3:08pm:
Thank you for the feedback. I already set the picture size to 4 x 6. This should create a pic of the right size, I will try tomorrow. Thank you again.


I'm not sure that will reduce the pixel size of the picture appropriately.  I have Photoshop that I use.  As Ian has recommended the link will assist you in resizing the pictures.  Usually when you hover your cursor over the saved file it will give you the size of the file that's been saved.
Tom
 

If God is your Co-pilot...switch seats...
Your attitude will determine your altitude!- John Maxwell
And ye shall know the truth, and the truth shall set you free. Jn 8:32
IP Logged
 
Reply #5 - Jan 10th, 2017 at 3:08pm

New Builder   Offline
Junior Member
Amherstburg, Ontario, Canada

Posts: 64
**
 
Thank you for the feedback. I already set the picture size to 4 x 6. This should create a pic of the right size, I will try tomorrow. Thank you again.
 
IP Logged
 
Reply #4 - Jan 10th, 2017 at 2:37pm

pb_guy   Offline
Senior Member
So I'm just a kid at heart.
Youbou, BC, Vancouver Island

Posts: 585
****
 
Don't worry about fiddling with camera settings. You need to get a photo resizing program. I use a free one called Irfanview. I select my photo, and under "Image" use "resize/resample". It has options to resize to particular pre-set size, or as a percentage of the original picture.
Irfanview available here: http://www.irfanview.com/
ian
 
IP Logged
 
Reply #3 - Jan 10th, 2017 at 12:42pm

New Builder   Offline
Junior Member
Amherstburg, Ontario, Canada

Posts: 64
**
 
Cut the post by 90% and one photo and still rejected. Queried the actual photo and the size is 1.77Mb. Can this be caused by the photo size setting on the camera?
 
IP Logged
 
Reply #2 - Jan 10th, 2017 at 12:15pm

New Builder   Offline
Junior Member
Amherstburg, Ontario, Canada

Posts: 64
**
 
Thanks for the feedback. I will try again.
 
IP Logged
 
Reply #1 - Jan 10th, 2017 at 10:17am

staubkorb   Offline
Senior Member
Stick & Tissue
Germany

Posts: 1122
****
 
Probably the attachments (photos) were too large, or the whole message was too long (large text and 6x 400Kb photos).

Explanation can be found HERE.
 

WWWoFF
Wonderful Wacky World of Free Flight
(with a bit of rc thrown in for giggles)

Comparing Spammers to a pile of organic waste is an insult to the organic waste!
IP Logged
 
Jan 10th, 2017 at 8:59am

New Builder   Offline
Junior Member
Amherstburg, Ontario, Canada

Posts: 64
**
 
Tried to popst my build this AM but kept getting the error that the request entity was too big and think my post was denied. Any guidance here?
 
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print