Welcome, Guest. Please Login or Register
Stick and Tissue Logo
 
  HomeHelpSearchLoginRegister  
 
 
Pages: 1 2 
Send Topic Print
Eze Dope (Read 1982 times)
Reply #17 - Mar 10th, 2019 at 4:31pm

Sky9pilot   Offline
Administrator
Stick & Tissue
Kelso, WA 98626 USA

Posts: 10743
*****
 
Walmart carries Hallmark tissue as well....you might check their supplies for various colors.
Tom
 

If God is your Co-pilot...switch seats...
Your attitude will determine your altitude!- John Maxwell
And ye shall know the truth, and the truth shall set you free. Jn 8:32
IP Logged
 
Reply #16 - Mar 10th, 2019 at 6:17am

New Builder   Offline
Senior Member
Amherstburg, Ontario, Canada

Posts: 989
****
 
Hi Paul - Yes it is domestic and is Hallmark tissue. I have tried others from the Dollar Store but they were a bit delicate for my method and the consistency is all over the map but Hallmark is very consistent in quality. For some reason Hallmark is available in many colors except yellow and it only comes four sheets to a package with several other colors, at least in the Wallmart store near me.
Mike
« Last Edit: Mar 10th, 2019 at 8:20am by New Builder »  

Have no fear of perfection - you'll never reach it. (Salvador Dali 1904 - 1989)
IP Logged
 
Reply #15 - Mar 9th, 2019 at 1:31pm

shipwreck   Offline
Senior Member
Navy Vet
Medina Ohio

Posts: 267
****
 
Hi Mike
Are you using domestic tissue?
Paul
 
IP Logged
 
Reply #14 - Mar 8th, 2019 at 8:30am

New Builder   Offline
Senior Member
Amherstburg, Ontario, Canada

Posts: 989
****
 
I use EZE Dope only and have no trouble with brushing it on. The fairly standard dilution of 30%/70% (dope/water) is about the best. My technique of using a brush varies quite a lot from most ideas about brushing. Most people hold the brush in a very upright manner and that pushes down on the tissue and risks a hole in the damp tissue. The picture is of the wing for my Mr. Mulligan from the Comet Cookup. I decided to recover it but was disappointed with the rather crude building technique I used so rebuilt and covered it. Covering is Hallmark tissue attached with UHU Clear glue stick and shrunk with water. The coating is one coat of EZE Dope and absolutely no mottling, puddling or runs. The pictures show the wing and the angle I use to hold the brush. The brush is an artists brush and called a mop. It is very soft and holds quite a lot of liquid. Dip only the tip into the dope, drain it slightly on the edge of the jar and drag it along the length of the item. Don't stop during the application as that will cause puddling and make sure there are no bare spots as they will show up when least expected and do not touch the area when done as this will definitely cause problems. I clean my brush in water and dish soap and have never had a problem with accumulated dry dope. I also comb out the bristles (probably a bit of OCD here but my workshop brushes are a good as new also) so they dry straight and stand the brush upright to dry.
Mike
 

DSC06931.jpg (76 KB | 15 )
DSC06931.jpg
DSC06930.jpg (80 KB | 18 )
DSC06930.jpg
DSC06929.jpg (81 KB | 14 )
DSC06929.jpg
DSC06928.jpg (80 KB | 15 )
DSC06928.jpg

Have no fear of perfection - you'll never reach it. (Salvador Dali 1904 - 1989)
IP Logged
 
Reply #13 - Mar 7th, 2019 at 7:56pm

shipwreck   Offline
Senior Member
Navy Vet
Medina Ohio

Posts: 267
****
 
I have been having some good luck with the EzeDope. Three light coats with a brush 40% EzeDope to 60% water. I have been pretty shrinking on a frame before applying to my light weight frames.
Paul
 
IP Logged
 
Reply #12 - Oct 18th, 2018 at 11:52am
Neoflight   Ex Member

 
Thanks for the heads up, Staubkorb. I've never used EzeDope but have given it a thought to try. Your experience cinches it for me. My airbrush is already very sensitive to water based acrylics. Eze won't be used.
 
IP Logged
 
Reply #11 - Sep 26th, 2018 at 6:43pm

staubkorb   Offline
Senior Member
Stick & Tissue
Germany

Posts: 1328
****
 
I ruined my cheapo airbrush using that gunk, even tho I immediately cleaned it (siphon-feed single action from REVELL).  The stuff dries ever so slightly in the time that one lets up on the spraying that it eventually clogs (if you get that far).  After one finishes "cleaning", the bit that has dried is not visible and is nearly impossible to remove - even acetone didn't help mine, plus plastic doesn't mix well with acetone.

YMMV...
 

WWWoFF
Wonderful Wacky World of Free Flight
(with a bit of rc thrown in for giggles)

Comparing Spammers to a pile of organic waste is an insult to the organic waste!
IP Logged
 
Reply #10 - Sep 26th, 2018 at 1:25pm

Sky9pilot   Offline
Administrator
Stick & Tissue
Kelso, WA 98626 USA

Posts: 10743
*****
 
I haven't tried airbrushing EzeDope...I'm a bit lazy and don't want to tear down the brush to clean the Ezedope completely out of the brush.  With the acrylics I'm able to clean with several douses of Windex through the brush into the cleaning bottle, made from an old 2 liter soda bottle.  Allows cleaning and eliminates over spray while cleaning.  That's another subject. 

You might try cutting another grey tissue pattern and apply it to the area.  Save masking for the airbrush and spraying the grey. 
Tom
« Last Edit: Sep 26th, 2018 at 2:33pm by Sky9pilot »  

If God is your Co-pilot...switch seats...
Your attitude will determine your altitude!- John Maxwell
And ye shall know the truth, and the truth shall set you free. Jn 8:32
IP Logged
 
Reply #9 - Sep 26th, 2018 at 11:37am

alfakilo   Offline
Senior Member
Retired USAF and TWA.
St Louis, MO

Posts: 837
****
 
I'll try that. I was quite concerned about poking thru the tissue when applying the thinned EZDope and consequently probably slopped it on too much. Maybe airbrushing is the better idea.
 
IP Logged
 
Reply #8 - Sep 26th, 2018 at 10:47am

Sky9pilot   Offline
Administrator
Stick & Tissue
Kelso, WA 98626 USA

Posts: 10743
*****
 
Gotta go thinner mix...at least 70/30 water/EzeDope and can't apply too heavily on each coat.  I believe the cause of the white spot is a bit of pooling of the application as it dries. Almost have to use a very dry brush or foam brush on application in my experience.
Tom
 

If God is your Co-pilot...switch seats...
Your attitude will determine your altitude!- John Maxwell
And ye shall know the truth, and the truth shall set you free. Jn 8:32
IP Logged
 
Reply #7 - Sep 26th, 2018 at 9:47am

alfakilo   Offline
Senior Member
Retired USAF and TWA.
St Louis, MO

Posts: 837
****
 
Has the mottled appearance in the EZDope finish been solved yet? I've read the suggested links and see the same whitish blemishes in my Loire46 wing. I use a 50/50 water mix, stirred not shaken, and brushed on. Haven't tried airbrushing yet.

I like the overall qualities of EZDope but have seen these blemishes before and would like to avoid them, if possible.
 

ezdope1.jpg (196 KB | 28 )
ezdope1.jpg
IP Logged
 
Reply #6 - Jul 14th, 2018 at 1:33pm

shipwreck   Offline
Senior Member
Navy Vet
Medina Ohio

Posts: 267
****
 
Thanks Tom
 
IP Logged
 
Reply #5 - Jul 13th, 2018 at 7:04pm

Sky9pilot   Offline
Administrator
Stick & Tissue
Kelso, WA 98626 USA

Posts: 10743
*****
 
couple of links listed below.  One goes to the tissue and finish board and the other goes to the Rutango build of Pete and Myself in the Any Twin Cookup... Here's a link to that referrence, you'll need to read a page or two to find all the details of the EzeDope.  Dilution formulas... I've settled on 70/30  water/EzeDope.  For brushing or spraying.  Even the second coat wrinkles the tissue but as it dries it shrinks back again.  Click Here
sky9pilot/Tom
 

If God is your Co-pilot...switch seats...
Your attitude will determine your altitude!- John Maxwell
And ye shall know the truth, and the truth shall set you free. Jn 8:32
IP Logged
 
Reply #4 - Jul 13th, 2018 at 1:17pm

shipwreck   Offline
Senior Member
Navy Vet
Medina Ohio

Posts: 267
****
 
Thanks i will check it out.
Paul
were would i find that?  Roll Eyes
 
IP Logged
 
Reply #3 - Jul 12th, 2018 at 7:43pm

Sky9pilot   Offline
Administrator
Stick & Tissue
Kelso, WA 98626 USA

Posts: 10743
*****
 
Check out the link to the Rutango because there's more details on the application of EzeDope and mixture.
Tom
 

If God is your Co-pilot...switch seats...
Your attitude will determine your altitude!- John Maxwell
And ye shall know the truth, and the truth shall set you free. Jn 8:32
IP Logged
 
Pages: 1 2 
Send Topic Print