Welcome, Guest. Please Login or Register
Stick and Tissue Logo
 
  HomeHelpSearchLoginRegister  
 
 
Pages: 1 ... 4 5 6 7 8 ... 28
Send Topic Print
Guillow's P-51D Mustang (yep, another one) (Read 25302 times)
Reply #339 - Jan 11th, 2020 at 5:56am

Kaintuck   Offline
Full Member
Controled landings are
best!
Lawrenceburg tn

Posts: 175
***
 
Gary..outstanding work!!!.....you have steady hands!....
You mentioned the skin following the outline....is it a skin that can be heated?...heat the edge then lay it on the wheel well?
Marc
« Last Edit: Jan 14th, 2020 at 6:32am by Kaintuck »  
IP Logged
 
Reply #338 - Jan 10th, 2020 at 10:55pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
Gentlemen,

I'm still working out the details on the interior of the wheel wells and haven't made much progress lately.  However, I'm always trying to think ahead so I can carefully plan for my next move.  At this point, I'm trying to figure out how to create the "lip" that surrounds the wheel well outline.  This "lip" allows the gear doors to slightly overlap and seal themselves in.

Any suggestions?  My covering will be Flite Metal which is the aluminum foil with a strong adhesive backing.  Once it touches the surface of anything, that's it.  It's stuck.  So I have to be really careful how to approach this method of creating this lip. 

Should I cut out a slightly smaller outline on a separate sheet of glossy paper or thin plastic sheet and carefully line it up with the outline of the underside surface?  How should I go about attaching the foil and making sure it follows the wheel well outline exactly as on the full sized aircraft?

As usual, my methods of scale modeling is always "outside the box" of easy ways of building.
 

(218 KB | 12 )
P-51_wheel_well_detail___109A_002.png
IP Logged
 
Reply #337 - Dec 24th, 2019 at 5:24pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
Tom and Mike,

Wow.  Thank you guys.  You really made my day with your comments.  It's greatly appreciated. 

Right now, I'll be working on the left wing which is similar to what's been accomplished here with the different plumbing and the added landing light. 

This shouldn't take too long as most of the trials and tribulations and studying of trying to figure out how all this was going to come together was done on the right wing. 

From there, I'll mate the two wing panels and start working on the center section which will include the actuators for the inner gear doors, mating of the main spars, and (trying to) figuring out how to finish off the ceiling of the interior with the accummators, gauges, more twisted plumbing, electrical wiring, and stuff.  When I get to that point, I'll keep everyone updated. 

Merry Christmas everyone.


.
 
IP Logged
 
Reply #336 - Dec 24th, 2019 at 8:34am

New Builder   Offline
Senior Member
Amherstburg, Ontario, Canada

Posts: 1225
****
 
Gary - Your work is truly great and can't wait for the reveal. If the Wright Flyer was any indication of your work, there will be another terrific model for everybody to drool over.
Mike
 

"Skill comes by the constant repetition of familiar feats rather than by a few overbold attempts for which the performer is yet poorly prepared." Wilbur Wright
IP Logged
 
Reply #335 - Dec 22nd, 2019 at 9:56pm

Sky9pilot   Offline
Administrator
Stick & Tissue
Kelso, WA 98626 USA

Posts: 11462
*****
 
Looks great!!! Smiley
 

If God is your Co-pilot...switch seats...
Your attitude will determine your altitude!- John Maxwell
And ye shall know the truth, and the truth shall set you free. Jn 8:32
IP Logged
 
Reply #334 - Dec 22nd, 2019 at 9:33pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
I decided to temporarily place the underside wing skin over the wheel well to see how it all comes together.

The cut outs holding up the "plumbing" really shows up to good effect here.  The actuator is in good position.  I did not try bending the tubes as I realized that it's nearly impossible to gain access to the tubes even with needle nosed pliers and tweezers (let alone my hands) within the small confines of the interior and bend them to connect to the actuator.  I also felt any attempts would simply end up ripping the interior anyway.  The tubing will have to be pre-bent and installed with a "connector" in between. 

Looking almost directly straight down, the actuator disappears, as it should, just like on the full sized Mustang.  The plumbing really appears 3-D.  I'm glad I took the extra steps of punching out the small holes in the ribs instead of taking the easy way out and simply gluing the plumbing onto the interior ceiling and main wing spar.

Score one for OCD.....  Grin

 

(83 KB | 8 )
P-51_wheel_well_detail___138A.jpg
(93 KB | 8 )
P-51_wheel_well_detail___139A.jpg
IP Logged
 
Reply #333 - Dec 22nd, 2019 at 9:21pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
As in many other aspects of this build, I had to make adjustments and in this case, reinforce the ribs.

The first picture is posed to show what I did to reinforce the ribs.  I would have to pre-paint the brackets before gluing them to the interior wall. 

The second picture shows the final results.  The paint did a great job of helping the brackets to blend in with the interior.  You really have to zoom up and look carefully, especially the first set nearest the wheel well, to see the brackets.   Whew...  now its back for another trial.
 

(98 KB | 9 )
P-51_wheel_well_detail___137A.jpg
(85 KB | 8 )
P-51_wheel_well_detail___140A.jpg
IP Logged
 
Reply #332 - Dec 22nd, 2019 at 9:13pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
The Litmus test is when I start to run some (sample) plumbing through the ribs.  After all, it's what all the fuss is about and the extra work.

Wow.  Initially I thought this would be a piece of cake and the rest is downhill.  The small tubing just slid right through the holes and everything lined up.

Unfortunately, when I tried to bend the plastic tubes to hook up to the actuator, however easy and light they are, the ribs started to buckle and move.  Apparently, the thin ribs just glued free-standing to the interior wasn't strong enough to withstand the bending loads. 
 

(95 KB | 7 )
P-51_wheel_well_detail___135A.jpg
(99 KB | 7 )
P-51_wheel_well_detail___136A.jpg
IP Logged
 
Reply #331 - Dec 22nd, 2019 at 8:58pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
Okay.  Let's put all of this together and see what happens starting with the finished rib in my hand as in the previous post.

Starting to look like a real honest-to-goodness wheel well interior.
 

(76 KB | 6 )
P-51_wheel_well_detail___132A_001.jpg
(103 KB | 7 )
P-51_wheel_well_detail___133A.jpg
(161 KB | 8 )
P-51_wheel_well_detail___128A_001.jpg
IP Logged
 
Reply #330 - Dec 21st, 2019 at 11:07pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
Skyper9,

Thank you, sir.  I'm hoping to achieve just that "change" you mentioned.  I won't know until the two wing panels are permanently glued together as the plumbing is dependent upon the center main rib that divides the wings under the fuselage. 

It's at this junction where the wheel is located is when we see all the plumbing start twisting every which way.  To be able to effectively match up the plumbing and the electrical conduits requires that everything be in its place and ready for me to "thread" the plumbing through the holes.  Or at least have them pre-inserted and have the excess ready for bending and twisting when the wings are joined.  I've been thinking alot on how to approach this.  Still not sure which course of action to take.


 
IP Logged
 
Reply #329 - Dec 21st, 2019 at 11:01pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
While observing the interior wheel well and its plumbing, wiring and conduits, I noticed that much of it actually goes through the wing ribs as well as being bolted or fastened to the main spar.  At first, I thought of simply gluing the plumbing and electrical wires to the ceiling of the interior and back to the main spar.  But that little ol' OCD kicked in and said: "Wouldn't be sooo cool to have the plumbing go through the ribs just like the full sized Mustang?"  It would also add some dimension to the eye-candy as the plumbing would stick out more and for the astute observers, would really knock 'em down. 

I had already punched out some holes for the main conduits but was concerned that too many small holes might distort the fragile ribs.  As it turned out, I was wrong.

I went back to use the small punch-n-die set and used one of the smaller punches.  As the first photo shows, they can really get small and down to scale almost as if the punch was more like a pin.

The second picture shows the holes for the plumbing to pass through the ribs near the "ceiling" of the interior wheel well.   

I also took advantage of the punch set and punched in some "half-round" holes at the rear edges of the ribs to allow room for the plumbing to pass through on the main wing spar.  Looking closely, you can see the rear half-round holes for the cut outs to be made.

The last two pictures show me using an X-Acto blade and cutting out between the two half-rounds.  The last picture shows the cut out.  The picture doesn't do justice, but its really neat and tidy.
 

(105 KB | 9 )
P-51_wheel_well_detail___129A.jpg
(100 KB | 13 )
P-51_wheel_well_detail___130A.jpg
(88 KB | 11 )
P-51_wheel_well_detail___131A.jpg
(76 KB | 12 )
P-51_wheel_well_detail___132A.jpg
IP Logged
 
Reply #328 - Dec 21st, 2019 at 10:48pm

Sky9pilot   Offline
Administrator
Stick & Tissue
Kelso, WA 98626 USA

Posts: 11462
*****
 
Amazing how a small touch like that can really change the looks of things! Smiley
 

If God is your Co-pilot...switch seats...
Your attitude will determine your altitude!- John Maxwell
And ye shall know the truth, and the truth shall set you free. Jn 8:32
IP Logged
 
Reply #327 - Dec 21st, 2019 at 9:56pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
First off, I noticed that area where the main landing gear strut will be located, it was just too green.  I felt it would look odd for the strut to suddenly appear out from nothing but green.  So a little bit of darkening was added here.

It really doesn't make much sense as the strut still appears out from nowhere, but at least it'll give the impression that the darkened background creates the illusion of the mechanics are too deep and hidden to be easily seen.

I didn't think that painting the whole background was necessary.  So I used a pen to denote the areas that would be seen through the rib and then brush-painted flat black.

If you compare this scene with the previous post where the actuator piston goes in to the last rib, it makes more visual sense.
 

(69 KB | 14 )
P-51_wheel_well_detail___119A.jpg
(68 KB | 17 )
P-51_wheel_well_detail___120A.jpg
(85 KB | 15 )
P-51_wheel_well_detail_110A.jpg
IP Logged
 
Reply #326 - Dec 21st, 2019 at 9:27pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
Looking at the plumbing within the well, I also noticed that much of the pipes and conduits go through the wing ribs.  I initially thought of skipping this stage and simply glue the plumbing on the ceiling inside the well and also on the main wing spar.  But then again, that little ol' OCD kicked in and I said to myself "Self, it would look sooo cool if the plumbing went through the ribs just like on the full sized Mustang."

I decided to use the third photo as my primary source, only because of how the silver plumbing contrasted beautifully against the green chromate background and provides some eye-candy when looking at the wheel well interior through the reflection in the mirror.  Pure artistic choice.  No logic whatsoever.

Common sense-wise, if doing the interior of the wheel well, the second photo would've made more sense as it doesn't have as much "activity" as the last picture.  I was also taking into account of how much visual contrast would be needed to see the interior of the wheel well when looking at it through the reflection in the mirror.




 

(226 KB | 11 )
P-51_wheel_well_detail___40A.png
(218 KB | 9 )
P-51_wheel_well_detail___109A_001.png
(201 KB | 9 )
P-51_wheel_well_detail___50A.png
IP Logged
 
Reply #325 - Dec 21st, 2019 at 9:10pm

Skyediamonds   Offline
Global Moderator
Enjoying life and all
aspects of modeling
Reno, Nevada

Posts: 2631
****
 
I'm jumping a little bit ahead of myself in posting this build of the actuator because I left out a couple of other steps I had to take before getting to the final installation within the wheel well. 

I used another, but smaller piece of plastic tubing to simulate the chromed strut that moves in and out of the actuator housing (piston).  I cut it to about the length that seemed to work and painted it silver.  I probably should've used a small slice of that highly polished film covering to wrap around this piston but since it's almost out of sight inside the wheel well, I figured a quick shot of silver paint should suffice. 

I'll definitely will use this Flite Metal to wrap around the piston of the inner gear door actuator since it will be more prominently seen.

The next steps will be the plumbing and electric wiring, but all that will have to wait until the left wing wheel well interior is completed as well as the additional actuators and stuff.

Whew, all this required a lot of thinking...and planning and adjusting.
 

(91 KB | 9 )
P-51_wheel_well_detail___118A.jpg
(89 KB | 9 )
P-51_wheel_well_detail___124A.jpg
(161 KB | 6 )
P-51_wheel_well_detail___128A.jpg
IP Logged
 
Pages: 1 ... 4 5 6 7 8 ... 28
Send Topic Print